How to Regrip a Golf Club

Having your golf clubs regripped used to be oddly expensive in addition to the expense of the new grips.  Thankfully, the going rate of having this service performed at a lot of shops has gone down, but that doesn’t mean you wouldn’t want to learn how to regrip a golf club yourself.  Learning to regrip your clubs can not only help you save a few bucks, but it also helps you make sure your grips are always installed exactly how you like them.  If you’re anything like me, you’ll also enjoy doing it occasionally as a recreational activity to do something golf related at your house.

Supplies

You can refer to my “Tools For an At Home Golf Workshop” post to see a detailed list of tools I recommend for regripping golf clubs and prices.  The quickest and easiest way to get setup to regrip a golf club is with the supplies listed below.

• Vise
• Vise Clamp
• Workbench
• Heat Gun or Propane Torch (not mandatory, but makes life way easier)
• Utility Knife with hook blades
• Grip Tape
• Grip Solvent
• Solvent Pan (or something else to capture spilling solvent)
• New Grips

Removing Old Grips

This process is fairly easy.  Keep in mind some grips are easier than others and it may take a little more effort than you’d expect.  Often times a grip with cord takes a little more fight.  Some people may want to save the grips for whatever reason, but that’s another post for another day.

If you just want to remove your old, dry, crusty, disgusting, smelly grips all you need is your hooked blade utility knife.  Start at the base of the grip and cut a straight line toward the butt end of the grip.  SAFETY TIP: make sure you always cut away from you.  That’s just good knife safety practices.  Once you make that cut, you will be able to peel the grip off.  You can further cut and adjust as necessary.

WARNING: There isn’t much risk with a steel shaft, but if you’re removing a grip from a graphite shaft BE CAREFUL to not scratch the graphite and damage the shaft.

Removing Old Tape

Old tape is generally the worst.  Especially if it was cheap, crappy tape.  It won’t come off easy no matter what you do.  The best tip I can give here is to use a heat gun or Propane torch to heat the tape up and break down the adhesive.  This will make peeling the tape much easier.

You can also use a straight utility blade to scrape it off in chunks, but if you do the above well, it will be more trouble than it’s worth.

If you have residue and whatnot left, use a little mineral spirits or solvent on a rag, some elbow grease, and remove it so the shaft is clean.

ANOTHER WARNING: Again, steel shafts are pretty safe, but BE CAREFUL with graphite.  Too much heat can cause bad structural problems to the graphite.  Don’t heat it too much.  Also, remember what I said about using a utility knife on a graphite shaft.

Tape ’em Up

Alright, got the old tape off so now we want something to create a little sticking friction for the grip and to take up any “space” between the grip and the shaft so it doesn’t move.  Some people use masking tape others use two-sided grip tape.  My preference is a good quality two-sided grip tape.

There’s more than one way to skin a cat.  Just make sure your finished product doesn’t have tape hanging out the bottom.  Some people will do that on purpose and then trim it off.  I personally don’t love that approach and measure so the end of my tape is just short of the bottom of the grip.

This may be the most important part of the tape step.  You need to make sure you leave a half inch or so of tape hanging off the butt of the club.  Once you wrap the tape around the shaft, twist this excess hanging tape to a point and just poke it down into the shaft.  This creates a “cover” to the shaft and prevents any grip solvent from getting in the shaft and breaking down any epoxy over time.

Apply New Grips

This is another area where there’s more than one way to skin a cat (or to regrip a golf club).  Some people prefer to use air compressors and no solvent, some like to use water and dish soap, some like to use mineral spirits…  Aside from air, the common practice is to fill the grip with your solvent (while covering the hole on the butt end), shake it to get the inside nice and coated (hold fingers over both ends so solvent doesn’t fly everywhere), and then pour it out over the grip tape (this is why you need something to catch the solvent in). I also like to give the tape an extra coat of solvent straight from the bottle for more stubborn grips.

At this point you can slide grip over the tape pretty effortlessly.

Check and make sure you have everything nice and straight, looks good to your eye, and feels good in your hands.  You can twist and adjust easily while the tape is still wet.

NOTE: The more layers of tape you use, the more difficult sliding the grip on can be.  Make sure you use plenty of solvent to create proper lubrication.

Dry Time

Grip solvent and mineral spirits dry pretty quickly, but you want to allow your grips adequate time to dry so they don’t twist.  I like to lean my newly gripped clubs straight up against a wall and give them at least six hours to dry.  Most times I’m gripping my clubs at night after the kids go to sleep so they just dry overnight.

Conclusion

There you have it.  The simple details of how to regrip a golf club in your own house.  There are more advanced tips, tricks, and efficiencies, but this is enough to get the job done and get you on your equipment tinkering way.

If you have any questions or comments, make sure you leave them below!

Previous Next